如何記錄單片機日志？

嵌入式大雜燴

關注+星標公眾號，不錯過精彩內容

素材來源 | 網絡
很多場景都需要記錄日志，在單片機這種存儲資源有限的環境下，就需要一種輕量級的存儲方法。
系統日志在嵌入式設備應用場景中，系統日志時常可以監控設備軟件的運行狀態，及時記錄問題點以及關鍵信息，方便開發人員后期定位以及解決問題。
本文將講述一種簡易的系統日志記錄方法，用于保存設備的系統日志，視具體嵌入式設備情況而定，可存儲在MCU內部Flash、外部Flash、EEPROM等，本文采用外部Flash作為示例展開介紹。
思路分析對于系統日志可以當成文件系統，可以劃分為三個重要部分：目錄區、參數區、日志區。

目錄區：根據日期進行歸類，記錄當天的日志的存儲地址、日志索引、日志大小，通過目錄可以獲取整個日志文件的概況；

參數區：存儲記錄日志寫位置、目錄項個數、寫狀態等參數；

日志區：這是我們主要的存儲區，記錄系統的日志，支持環寫。這三個區域都需要占用部分內存，可以自行分配大小。
實現的效果如下圖所示，設置通過指令可查詢到整個日志目錄區的概況。查詢系統日志目錄：AT+CATALOG?LOG_ID:存儲日志按日期分類，該ID用于查詢對應日期日志,從1開始計數；LOG_DATE:系統日志存儲日期；LOG_ADDR:系統日志存儲外部FLASH地址；LOG_OFFSET:系統日志存儲偏移量（各日期日志大小，單位：字節）。

查詢指定日期系統日志：AT+CATALOG=LOG_ID:在查詢系統日志目錄時獲取，當LOG_ID為0時，為查詢整個系統日志。

另外提供移除系統日志（清除日志目錄）指令：AT+RMLOG，后面將講述具體實現。
FLASH內存劃分FLASH內存需要看具體設備進行合理劃分，目錄區、參數區與日志區實現環形存儲，延長擦寫壽命。

#define FLASH_SECTOR_SIZE      ((uint32_t)0x001000)#define FLASH_BLOCK_32K_SIZE    ((uint32_t)0x008000)#define FLASH_BLOCK_64K_SIZE    ((uint32_t)0x010000)#define SECTOR_MASK               (FLASH_SECTOR_SIZE - 1)         /*扇區掩碼 ------*/#define SECTOR_BASE(addr)         (addr & (~SECTOR_MASK))        /*扇區的基地址 --*/#define SECTOR_OFFSET(addr)       (addr & SECTOR_MASK)           /*扇區內的偏移 --*/
#define BLOCK_32K_BASE(addr)    (addr & (~(FLASH_BLOCK_32K_SIZE)))#define BLOCK_64K_BASE(addr)    (addr & (~(FLASH_BLOCK_64K_SIZE)))
typedef enum {    FLASH_BLOCK_4K  = 0,          /**    FLASH_BLOCK_32K = 1,          /**    FLASH_BLOCK_64K = 2           /**}flash_block_t;
/* flash 空間索引 */typedef enum{    FLASH_CATALOG_ZONE = 0,    FLASH_SYSLOG_PARA_ZONE,    FLASH_SYSLOG_ZONE,    FLASH_ZONEX,}flash_zone_e;
typedef struct{    flash_zone_e zone;    uint32_t start_address;    uint32_t end_address;}flash_table_t;
/* 地址劃分 */static const flash_table_t flash_table[] = {  { .zone = FLASH_CATALOG_ZONE,       .start_address = 0x03200000, .end_address = 0x032FFFFF},    { .zone = FLASH_SYSLOG_PARA_ZONE,   .start_address = 0x03300000, .end_address = 0x033FFFFF},    { .zone = FLASH_SYSLOG_ZONE,        .start_address = 0x03400000, .end_address = 0x03FFFFFF},  };
Flash底層實現擦除、讀寫操作接口，由讀者自行實現。

flash_table_t *get_flash_table(flash_zone_e zone){  int i = 0;  for (i = 0; i     if (zone == flash_table.zone)       return (flash_table_t *)&flash_table;  }
  return NULL;  }
int flash_erase(flash_zone_e zone, uint32_t address, flash_block_t block_type){  flash_table_t *flash_table_tmp = get_flash_table(zone);
  if (flash_table_tmp == NULL)    return -1;
  if (address start_address ||address > flash_table_tmp->end_address)     return -1;
  return bsp_spi_flash_erase(address, block_type);}
int flash_write(flash_zone_e zone, uint32_t address, const uint8_t*data, uint32_t length){  flash_table_t *flash_table_tmp = get_flash_table(zone);
  if (flash_table_tmp == NULL)     return -1;
  if ((address start_address) ||((address + length) > flash_table_tmp->end_address))     return -1;
  return bsp_spi_flash_buffer_write(address, (uint8_t *)data, length);}
int flash_read(flash_zone_e zone, uint32_t address, uint8_t*buffer, uint32_t length){  flash_table_t *flash_table_tmp = get_flash_table(zone);
  if (flash_table_tmp == NULL)    return -1;
  if ((address start_address) ||((address + length) > flash_table_tmp->end_address))    return -1;
  bsp_spi_flash_buffer_read(buffer, address, length);  return 0;}
參數與結構體定義日志數據存儲時間戳，便于問題定位，需要實現RTC接口調用。

typedef struct {  uint16_t   Year;    /* 年份:YYYY */  uint8_t    Month;    /* 月份:MM */  uint8_t    Day;    /* 日:DD */  uint8_t     Hour;    /* 小時:HH */  uint8_t     Minute;    /* 分鐘:MM */  uint8_t   Second;    /* 秒:SS */}time_t;   
int bsp_rtc_get_time(time_t *date);
參數區應當保證數據的正確性，應加入?yún)��?shù)校驗存儲，定義校驗結構體。

#define SYSTEM_LOG_MAGIC_PARAM    0x87654321  /* 日志參數標識符 */typedef struct {  uint32_t magic;    /* 參數標識符 */  uint16_t crc;    /* 校驗值 */  uint16_t len;    /* 參數長度 */} single_sav_t;
參數區需記錄當前日志記錄的寫位置，以及目錄項個數，還有日志區和目錄區環寫狀態，并且存儲最新時間等等。

/* 日志區參數 */typedef struct {  uint32_t   write_pos;             /* 寫位置 */  uint32_t   catalog_num;            /* 目錄項個數 */  uint8_t    log_cyclic_status;    /* 系統日志環形寫狀態 */     uint8_t    catalog_cyclic_status; /* 日志目錄環形寫狀態 */  time_t     log_latest_time;     /* 存儲最新時間 */}system_log_t;
/* 目錄區參數 */typedef struct {  uint32_t log_id;     /* 日志索引 */    uint32_t log_addr;    /* 日志地址 */  uint32_t log_offset;  /* 日志偏移大小，單位：字節 */  time_t   log_time;    /* 日志存儲時間 */}system_catalog_t;
/* 系統日志參數 */typedef struct {  single_sav_t crc_val;  system_log_t system_log;  system_catalog_t system_catalog;}sys_log_param_t;
typedef struct {  uint8_t system_log_print_enable; /* 系統日志打印使能 */  uint16_t system_log_print_id;    /* 打印指定id系統日志 */  uint32_t system_log_param_addr;  /* 當前日志寫地址 */} sys_ram_t;
sys_ram_t  SysRam;sys_log_param_t SysLogParam;
sys_ram_t  *gp_sys_ram = &SysRam;sys_log_param_t *gp_sys_log = &SysLogParam;
實現接口說明CRC校驗接口，可以自定義實現。

/* 16位CRC校驗高位表 */static const uint8_t auchCRCHi[]={0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40};
/* 16位CRC校驗低位表 */static const uint8_t auchCRCLo[]={0x00,0xc0,0xc1,0x01,0xc3,0x03,0x02,0xc2,0xc6,0x06,0x07,0xc7,0x05,0xc5,0xc4,0x04,0xcc,0x0c,0x0d,0xcd,0x0f,0xcf,0xce,0x0e,0x0a,0xca,0xcb,0x0b,0xc9,0x09,0x08,0xc8,0xd8,0x18,0x19,0xd9,0x1b,0xdb,0xda,0x1a,0x1e,0xde,0xdf,0x1f,0xdd,0x1d,0x1c,0xdc,0x14,0xd4,0xd5,0x15,0xd7,0x17,0x16,0xd6,0xd2,0x12,0x13,0xd3,0x11,0xd1,0xd0,0x10,0xf0,0x30,0x31,0xf1,0x33,0xf3,0xf2,0x32,0x36,0xf6,0xf7,0x37,0xf5,0x35,0x34,0xf4,0x3c,0xfc,0xfd,0x3d,0xff,0x3f,0x3e,0xfe,0xfa,0x3a,0x3b,0xfb,0x39,0xf9,0xf8,0x38,0x28,0xe8,0xe9,0x29,0xeb,0x2b,0x2a,0xea,0xee,0x2e,0x2f,0xef,0x2d,0xed,0xec,0x2c,0xe4,0x24,0x25,0xe5,0x27,0xe7,0xe6,0x26,0x22,0xe2,0xe3,0x23,0xe1,0x21,0x20,0xe0,
0xa0,0x60,0x61,0xa1,0x63,0xa3,0xa2,0x62,0x66,0xa6,0xa7,0x67,0xa5,0x65,0x64,0xa4,0x6c,0xac,0xad,0x6d,0xaf,0x6f,0x6e,0xae,0xaa,0x6a,0x6b,0xab,0x69,0xa9,0xa8,0x68,0x78,0xb8,0xb9,0x79,0xbb,0x7b,0x7a,0xba,0xbe,0x7e,0x7f,0xbf,0x7d,0xbd,0xbc,0x7c,0xb4,0x74,0x75,0xb5,0x77,0xb7,0xb6,0x76,0x72,0xb2,0xb3,0x73,0xb1,0x71,0x70,0xb0,0x50,0x90,0x91,0x51,0x93,0x53,0x52,0x92,0x96,0x56,0x57,0x97,0x55,0x95,0x94,0x54,0x9c,0x5c,0x5d,0x9d,0x5f,0x9f,0x9e,0x5e,0x5a,0x9a,0x9b,0x5b,0x99,0x59,0x58,0x98,0x88,0x48,0x49,0x89,0x4b,0x8b,0x8a,0x4a,0x4e,0x8e,0x8f,0x4f,0x8d,0x4d,0x4c,0x8c,0x44,0x84,0x85,0x45,0x87,0x47,0x46,0x86,0x82,0x42,0x43,0x83,0x41,0x81,0x80,0x40};
/* 實現crc功能函數 */static uint16_t CRC16(uint8_t* puchMsg, uint16_t usDataLen){  uint8_t uchCRCHi=0xff;  uint8_t uchCRCLo=0xff;  uint16_t uIndex;
  while(usDataLen--) {    uIndex=uchCRCHi^*(puchMsg++);    uchCRCHi=uchCRCLo^auchCRCHi[uIndex];    uchCRCLo=auchCRCLo[uIndex];  }
  return uchCRCHi}
保存系統日志參數，每實現寫日志操作后都需要保存當前的參數值，防止意外丟失。

void save_system_log_param(void){  uint32_t i = 0;  uint32_t addr = 0;  uint32_t remainbyte = 0;  uint32_t start_addr;  int len = sizeof(sys_log_param_t);  uint8_t *pdata = (uint8_t *)&SysLogParam;  flash_table_t *flash_tmp = get_flash_table(FLASH_SYSLOG_PARA_ZONE);
  /* 校驗參數 */  gp_sys_log->crc_val.magic = SYSTEM_LOG_MAGIC_PARAM;  gp_sys_log->crc_val.len = sizeof(sys_log_param_t) - sizeof(single_sav_t);  gp_sys_log->crc_val.crc = CRC16(&pdata[sizeof(single_sav_t)], gp_sys_log->crc_val.len);
  start_addr = gp_sys_ram->system_log_param_addr;  /* 剩余內存不夠?qū)�，則重新從起始地址開始寫，實現環形存儲功能  */  if ((start_addr + len) > flash_tmp->end_address) {     start_addr = flash_tmp->start_address;  }  gp_sys_ram->system_log_param_addr = start_addr + len;  /* 首地址存儲，擦除整個系統日志參數存儲區，如果劃分的內存較大，可能出現第一次擦寫等待時間較長，     但實際應用嵌入式設備應該不會占用太多的內存存儲系統日志，只當為輔助使用，有額外應用可自行實現 */  if (flash_tmp->start_address == start_addr) {    /*for (i = flash_tmp->start_address; i end_address; i+= FLASH_SECTOR_SIZE)       flash_erase(FLASH_SYSLOG_PARA_ZONE, SECTOR_BASE(i), FLASH_BLOCK_4K);    */    addr = flash_tmp->start_address;    do {      if ((addr + FLASH_BLOCK_64K_SIZE) end_address) {        flash_erase(FLASH_SYSLOG_PARA_ZONE, BLOCK_64K_BASE(i), FLASH_BLOCK_64K);        addr += FLASH_BLOCK_64K_SIZE;      } else if ((addr + FLASH_BLOCK_32K_SIZE) end_address) {        flash_erase(FLASH_SYSLOG_PARA_ZONE, BLOCK_32K_BASE(i), FLASH_BLOCK_32K);        addr += FLASH_BLOCK_32K_SIZE;      } else if ((addr + FLASH_SECTOR_SIZE) end_address) {        flash_erase(FLASH_SYSLOG_PARA_ZONE, SECTOR_BASE(i), FLASH_BLOCK_4K);        addr += FLASH_SECTOR_SIZE;      } else {        break;      }    } while (addr end_address);    }
  remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);  if (remainbyte > len) {    remainbyte = len;  }  while (1) {    flash_write(FLASH_SYSLOG_PARA_ZONE, start_addr, pdata, remainbyte);    if (remainbyte == len) {      break;    } else {      pdata += remainbyte;      start_addr += remainbyte;      len -= remainbyte;      remainbyte = (len > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : len;    }  }}
導入系統日志默認參數接口，初始化默認參數或者移除日志。

void load_system_log_default_param(void){  /* 系統日志默認參數 */  /* 目錄環寫狀態標志 */  gp_sys_log->system_log.catalog_cyclic_status = 0x00;  /* 目錄項個數 */  gp_sys_log->system_log.catalog_num = 0;  /* 日志環寫標志 , 1:環寫狀態 */  gp_sys_log->system_log.log_cyclic_status = 0;  /* 設置默認值，實際會重新從RTC獲取最新時間 */  gp_sys_log->system_log.log_latest_time.Year = 2019;  gp_sys_log->system_log.log_latest_time.Month = 5;  gp_sys_log->system_log.log_latest_time.Day = 8;  gp_sys_log->system_log.log_latest_time.Hour = 13;  gp_sys_log->system_log.log_latest_time.Minute = 14;  gp_sys_log->system_log.log_latest_time.Second = 10;  /* 日志寫位置從0開始 */  gp_sys_log->system_log.write_pos = 0;
  gp_sys_log->system_catalog.log_addr = 0;  gp_sys_log->system_catalog.log_id = 0;  gp_sys_log->system_catalog.log_offset = 0;  gp_sys_log->system_catalog.log_time.Year = 2019;  gp_sys_log->system_catalog.log_time.Month = 5;  gp_sys_log->system_catalog.log_time.Day = 8;  gp_sys_log->system_catalog.log_time.Hour = 12;  gp_sys_log->system_catalog.log_time.Minute = 12;  gp_sys_log->system_catalog.log_time.Second = 14;
  gp_sys_log->crc_val.magic = SYSTEM_LOG_MAGIC_PARAM;
  /* 導入默認參數后進行保存 */  save_system_log_param();}
設備開機或者復位都會進行導入系統日志參數操作，恢復日志讀寫參數，參數區為頻繁讀寫操作區域，每一次寫操作都會進行一次偏移，有效的導入?yún)��?shù)方法是從參數區結束地址到起始地址進行掃描，掃描不到合法的參數則會導入默認日志參數。

/* 參數初始化，在終端啟動時調用 */int load_system_log_param(void){  uint32_t i = 0;  single_sav_t psav;  uint32_t end_addr;  uint32_t interal = sizeof(sys_log_param_t);  int data_len = sizeof(sys_log_param_t) - sizeof(single_sav_t);  uint8_t *pram = (uint8_t *)&SysLogParam;  flash_table_t *flash_tmp = get_flash_table(FLASH_SYSLOG_PARA_ZONE);
  end_addr =flash_tmp->end_address - (flash_tmp->end_address - flash_tmp->start_address) % interal;  for (i = end_addr - interal; i > flash_tmp->start_address; i -= interal) {    flash_read(FLASH_SYSLOG_PARA_ZONE, i, (uint8_t *)&psav, sizeof(single_sav_t));    if ((psav.magic == SYSTEM_LOG_MAGIC_PARAM) && (psav.len ==data_len)) {            flash_read(FLASH_SYSLOG_PARA_ZONE, i + sizeof(single_sav_t), &pram[sizeof(single_sav_t)], data_len);      if (psav.crc != CRC16(&pram[sizeof(single_sav_t)], data_len))         continue;      gp_sys_ram->system_log_param_addr = i;      log_info("Load System Log Param Addr[0x%08x]!", gp_sys_ram->system_log_param_addr);      return 0;    }  }
  /* 掃描不到合法的參數，導入默認系統日志參數 */  load_system_log_default_param();  /* 獲取日志寫地址 */  gp_sys_ram->system_log_param_addr = flash_tmp->start_address;  log_info("Load System Log Param Addr(Default)[0x%08x]!", gp_sys_ram->system_log_param_addr);  return 1;}
讀寫系統日志目錄接口，讀寫指定日志索引目錄信息。實際實現會定義最新的目錄信息存儲在日志參數區，當日期發生改變，則表示當前目錄信息已經完結，將最新的目錄信息錄入日志目錄區保存，最多每天寫入一次目錄區。

/* 讀取日志目錄區指定日志索引目錄信息 */int system_catalog_read(system_catalog_t *catalog, uint32_t id){  uint32_t addr;  int rlen = sizeof(system_catalog_t);  uint8_t *pbuf = (uint8_t *)catalog;  flash_table_t *flash_tmp = get_flash_table(FLASH_CATALOG_ZONE);
  if (0 == id)     return -1;  addr = flash_tmp->start_address + (rlen * (id - 1));  if (addr > flash_tmp->end_address)     return -1;
  return flash_read(FLASH_CATALOG_ZONE, addr, pbuf, rlen);}
/* 寫日志目錄區目錄信息 */int system_catalog_write(system_catalog_t *catalog, uint32_t id){  uint32_t start_offset;  uint32_t start_addr;  uint32_t start_base;  uint32_t remainbyte;  int wlen = sizeof(system_catalog_t);  uint8_t *pdata = (uint8_t *)catalog;  flash_table_t *flash_tmp = get_flash_table(FLASH_CATALOG_ZONE);
  if (0 == id) return -1;  start_addr = flash_tmp->start_address + wlen * (id - 1);  if ((start_addr + wlen) > flash_tmp->end_address) {    start_addr = flash_tmp->start_address;  }
  /* 本扇區剩余空間大小 */  remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);  /* 寫入數據長度小于本扇區剩余長度，直接寫入 */  if (remainbyte > wlen) {    remainbyte = wlen;  }  /* 寫目錄次數不會太頻繁，視具體情況改寫操作實現 */  while (1) {    start_base = SECTOR_BASE(start_addr);      start_offset = SECTOR_OFFSET(start_addr);    flash_read(FLASH_CATALOG_ZONE, start_base, sector_buf, FLASH_SECTOR_SIZE);    flash_erase(FLASH_CATALOG_ZONE, start_base, FLASH_BLOCK_4K);    memcpy((char *)&sector_buf[start_offset], pdata, remainbyte);    flash_write(FLASH_CATALOG_ZONE, start_base, sector_buf, FLASH_SECTOR_SIZE);    if (remainbyte == wlen) {      break;    } else {      pdata += remainbyte;      start_addr += remainbyte;      wlen -= remainbyte;      remainbyte = (wlen > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : wlen;    }  }
  return 0;}
打印系統日志目錄區信息，可實現通過指令查詢到目錄區信息。

int system_catalog_all_print(void){  int i = 0;  system_catalog_t catalog;
  printf("System Log Command Information:\r
");  printf("Query Specifies Log : AT+CATALOG=\r
");  printf("Query All Log : AT+CATALOG=\r
\r
");  printf("Query All System Catalog:\r
");  printf("LOG_ID    LOG_DATE    LOG_ADDR    LOG_OFFSET  \r
");  for (i = 0; i system_log.catalog_num; i++) {    /* 當前最新目錄信息 */        if (i == (gp_sys_log->system_catalog.log_id - 1)) {      catalog = gp_sys_log->system_catalog; /* 獲取當前最新目錄信息 */    } else {      system_catalog_read(&catalog, i + 1);    }    printf("%d    %04d-%02d-%02d    0x%08X    %d  \r
",       catalog.log_id, catalog.log_time.Year, catalog.log_time.Month, catalog.log_time.Day,       catalog.log_addr, catalog.log_offset);    memset((char *)&catalog, 0, sizeof(system_catalog_t));  }  return 0;}
讀取指定日志目錄索引信息接口，可指定日志索引或者讀取全部日志數據。

int system_log_task(int argc){  int rlen = 0;  uint32_t offset, start_addr, end_addr;  system_catalog_t catalog;  flash_table_t *flash_tmp =get_flash_table(FLASH_SYSLOG_ZONE);
  if (0 == gp_sys_ram->system_log_print_enable)     return 1;
  gp_sys_ram->system_log_print_enable = 0x00;  if (gp_sys_ram->system_log_print_id == ALL_LOG_PRINT) {    /* log回環寫標志,打印整個LOG存儲區 */    if (0x01 == gp_sys_log->system_log.log_cyclic_status) {       start_addr = flash_tmp->start_address;      end_addr = flash_tmp->end_address;      offset = end_addr - start_addr;    } else {      start_addr = flash_tmp->start_address;      end_addr = start_addr + gp_sys_log->system_log.write_pos;      offset = gp_sys_log->system_log.write_pos;    }  } else { /* 讀取指定ID日志 */    if (gp_sys_ram->system_log_print_id == gp_sys_log->system_catalog.log_id) {      catalog = gp_sys_log->system_catalog;    } else {      system_catalog_read(&catalog, gp_sys_ram->system_log_print_id);    }    start_addr = catalog.log_addr;    offset = catalog.log_offset;  }  
  if (0 == offset)    return 1;
  while (1) {    rlen = (offset > 512) ? 512 : offset;    system_log_read(sector_buf, start_addr, rlen);    HAL_Delay(80);    /* 目錄信息通過調式串口打印 */    bsp_debug_send(sector_buf, rlen);    start_addr += rlen;    offset -= rlen;    if (0 == offset)       break;  }  return 0;}
存儲系統日志接口，實現更新存儲日期，當寫位置為扇區地址，則擦除一個扇區作為存儲日志，這樣避免每寫一次就擦除一次。

int system_log_write(uint8_t *wbuf, int wlen){  uint32_t start_addr;  uint8_t *pdata = wbuf;  uint32_t remainbyte;  int system_catalog_max_id;  flash_table_t *flash_tmp =get_flash_table(FLASH_SYSLOG_ZONE);
  /* 計算目錄區的最大存儲目錄項個數 */  system_catalog_max_id = ((flash_tmp->end_address - flash_tmp->start_address) / sizeof(system_catalog_t));  start_addr = flash_tmp->start_address + gp_sys_log->system_log.write_pos;  /* 存儲數據地址大于規劃內存地址范圍處理 */  if ((start_addr + wlen) > flash_tmp->end_address) {     start_addr = flash_tmp->start_address;    /* 寫位置偏移量重置 */    gp_sys_log->system_log.write_pos = 0;    /* LOG回環存儲標志置位 */    gp_sys_log->system_log.log_cyclic_status = 0x01;   }  /* 寫位置偏移 */  gp_sys_log->system_log.write_pos += wlen;
  if ((gp_sys_log->system_log.log_latest_time.Year != gp_sys_log->system_catalog.log_time.Year) ||    (gp_sys_log->system_log.log_latest_time.Month != gp_sys_log->system_catalog.log_time.Month) ||    (gp_sys_log->system_log.log_latest_time.Day != gp_sys_log->system_catalog.log_time.Day)) {
    /* 日期改變，記錄目錄信息，當log_id為0，則不寫入 */    system_catalog_write(&gp_sys_log->system_catalog, gp_sys_log->system_catalog.log_id);    /* 記錄存儲日期 */    gp_sys_log->system_catalog.log_time = gp_sys_log->system_log.log_latest_time;
    if ((gp_sys_log->system_catalog.log_id + 1) >= system_catalog_max_id) {      gp_sys_log->system_log.catalog_num = system_catalog_max_id; /* 目錄循環寫，目錄數應為最大 */      gp_sys_log->system_log.catalog_cyclic_status = 1; /* 目錄回環寫標志 */    } else {      if (0 == gp_sys_log->system_log.catalog_cyclic_status) {        /* 獲取目錄數 */        gp_sys_log->system_log.catalog_num = gp_sys_log->system_catalog.log_id + 1;       }    }
    /* 存儲最新目錄項信息 */    gp_sys_log->system_catalog.log_id = (gp_sys_log->system_catalog.log_id + 1) % system_catalog_max_id;    gp_sys_log->system_catalog.log_addr = start_addr;    gp_sys_log->system_catalog.log_offset = wlen;   } else {    gp_sys_log->system_catalog.log_offset += wlen;   }
  /* 寫位置為存儲起始地址并且不為扇區首地址 */  if ((flash_tmp->start_address == start_addr) && (SECTOR_OFFSET(flash_tmp->start_address))){    flash_read(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), sector_buf, FLASH_SECTOR_SIZE);    flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);    /* 將扇區頭部至起始地址區間的數據回寫 */    flash_write(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), &sector_buf[0], SECTOR_OFFSET(start_addr));   }  /* 寫位置為扇區首地址，則擦除一個扇區的存儲區    */  if (0 == SECTOR_OFFSET(start_addr)) {    flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);  }
  /* 本扇區剩余空間大小 */  remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);  /* 寫入數據長度小于本扇區剩余長度，直接寫入 */  if (remainbyte > wlen) {    remainbyte = wlen;  }  while (1) {    flash_write(FLASH_SYSLOG_ZONE, start_addr, pdata, remainbyte);    if (remainbyte == wlen) {      break;    } else {      pdata += remainbyte;      start_addr += remainbyte;      wlen -= remainbyte;      remainbyte = (wlen > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : wlen;      /* 扇區首地址則擦除整個扇區，該扇區數據不保存 */      if (0 == SECTOR_OFFSET(start_addr)) {        flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);      }    }  }
  /* 環形存儲參數 */  save_system_log_param();  return 0;}
系統調試對接為了更好記錄系統日志，將應用調試等級結合一塊，實現記錄錯誤調試信息以及需要保存的關鍵信息。定義的調試等級有：關閉調試等級、錯誤調試等級、警告調試等級、關鍵調試等級、debug調試等級，而LOG_RECORD_LEVEL將主動保存日志并輸出信息，LOG_ERROR_LEVEL會存儲對應的日志信息，但需要根據應用調試等級輸出信息。設置與讀取應用調試等級由讀者自行定義。

#define LOG_CLOSE_LEVEL        0x00 /* 關閉調試信息 */#define LOG_ERROR_LEVEL        0x01 /* 錯誤調試信息 */#define LOG_WARN_LEVEL        0x02 /* 警告調試信息 */#define LOG_INFO_LEVEL        0x03 /* 關鍵調試信息 */#define LOG_DEBUG_LEVEL        0x04 /* debug調試信息 */#define LOG_RECORD_LEVEL      0x10 /* 保存日志并輸出信息 */  #define LOG_PRINT_LEVEL        0xff
#define SET_LOG_LEVEL(LEVEL)    (gp_sys_param->system_print_level = LEVEL)#define GET_LOG_LEVEL()        (gp_sys_param->system_print_level)
#define log_debug(fmt, args...)    log_format(LOG_DEBUG_LEVEL, fmt, ##args)#define log_info(fmt, args...)    log_format(LOG_INFO_LEVEL, fmt, ##args)#define log_warn(fmt, args...)    log_format(LOG_WARN_LEVEL, fmt, ##args)#define log_error(fmt, args...)    log_format(LOG_ERROR_LEVEL, fmt, ##args)#define log_record(fmt, args...)  log_format(LOG_RECORD_LEVEL, fmt, ##args)#define printf(fmt, args...)    log_format(LOG_PRINT_LEVEL, fmt, ##args)
typedef struct {  int level;  char *fmt_str;}system_print_fmt_t;
system_print_fmt_t system_print_fmt_list[] = {  { .level = LOG_ERROR_LEVEL,   .fmt_str = ":"},  { .level = LOG_WARN_LEVEL,    .fmt_str = ":"},  { .level = LOG_INFO_LEVEL,    .fmt_str = ":"},  { .level = LOG_DEBUG_LEVEL,   .fmt_str = ":"},  { .level = LOG_RECORD_LEVEL,  .fmt_str = ":"},};
int log_format(uint8_t level, const char *fmt, ...){  #define TIME_PREFIX_SIZE  (21)  #define PRINT_MAX_SIZE    (1024 + TIME_PREFIX_SIZE)
    va_list args;    int num = 0, i = 0, fmt_index = 0;    int fmt_str_len = 0, ret = -1;    int file_str_len = 0, line_str_len = 0;    char line_buf[20] = {0};    static char buf[PRINT_MAX_SIZE];  static QueueHandle_t sem = NULL;  time_t time = {0};
  /* 針對os系統 */  if (NULL == sem) {        sem = xSemaphoreCreateCounting(1, 1); /* always think of success */  }
  xSemaphoreTake(sem, portMAX_DELAY);
  ret = -1;  fmt_str_len = 0;  if (level != LOG_PRINT_LEVEL) {    if ((GET_LOG_LEVEL()       goto exit_end;
    for (i = 0; i       if (level == system_print_fmt_list.level) {        fmt_index = i;        break;      }    }    if (i > SYSTEM_PRINT_FMT_LIST_MAX) {      goto exit_end;    }
    fmt_str_len = strlen(system_print_fmt_list[fmt_index].fmt_str);    strncpy((char *)&buf[TIME_PREFIX_SIZE], system_print_fmt_list[fmt_index].fmt_str, fmt_str_len);  }
    va_start(args, fmt);    num = vsnprintf((char *)&buf[fmt_str_len + TIME_PREFIX_SIZE], PRINT_MAX_SIZE - fmt_str_len - TIME_PREFIX_SIZE - 2, fmt, args);    va_end(args);
    if (num 0) {    goto exit_end;    }
  if (level != LOG_PRINT_LEVEL) {    num += fmt_str_len;    buf[num + TIME_PREFIX_SIZE] = '\r';    buf[num + TIME_PREFIX_SIZE + 1] = '
';    num += 2;  }
  if ((GET_LOG_LEVEL()     //do nothing  } else {    ret = bsp_debug_send((uint8_t*)&buf[TIME_PREFIX_SIZE], num);    }
  if ((LOG_ERROR_LEVEL == level) || (LOG_RECORD_LEVEL == level)) {    bsp_rtc_get_time(&time);    sprintf(&buf[0], "[%04d-%02d-%02d %02d:%02d:%02d",      time.Year, time.Month, time.Day,time.Hour, time.Minute, time.Second);    buf[TIME_PREFIX_SIZE - 1] = ']';    gp_sys_log->system_log.log_latest_time = time;    system_log_write((uint8_t *)buf, num + TIME_PREFIX_SIZE);  }  
exit_end:  xSemaphoreGive(sem);  return ret;}
結語本文提供的一種簡易嵌入式設備系統日志記錄方法，代碼量不多，實現簡單，針對不同的設備需要合理規劃內存使用。
根據軟件運行狀態，合適加入調試信息并保存對應的日志信息，方便開發人員了解系統或軟件運行狀況，協助開發分析數據資源從而更好完善系統，提高定位以及解決問題的效果。來源地址：https://blog.csdn.net/LiaRonBob/article/details/102766871聲明：本文素材來源網絡，版權歸原作者所有。如涉及作品版權問題，請與我聯系刪除。
猜你喜歡：
WiFi6+藍牙+星閃，三合一開發板，真香！
Github上熱門 C 語言項目匯總！
嵌入式，可測試性軟件設計！
一些低功耗軟件設計的要點！
嵌入式 C 保護結構體的方式
實用 | 10分鐘教你通過網頁點燈
談?wù)勄度胧杰浖�的兼容性�?/strong>